Tennsco Deluxe Cabinet CVD2470, Tennsco CVD2470 Deluxe Cabinet with C-Thru Doors

Tennsco Deluxe Cabinet CVD2470, Tennsco CVD2470 Deluxe Cabinet with C-Thru Doors, sets the standard for quality, convenience, and performance for over 30 years. These C-Thru Storage Cabinets are the perfect solution for viewing the contents of cabinets without violating people's privacy in schools, industrial applications, airports, prisons, and other workspace environments. 

CVD2470 is a heavy-duty cabinet that comes with a C through doors that features a high-quality finish and is fabricated of high-quality, cold-rolled carbon steel, free of scale or rust, and fully pickled. Partition shelves are formed with 22 gauge steel and have 1 1 / 8 Inches flanges at the rear and end. They have a channel formation in front and are adjustable on 2 Inch increments.

 Tennsco CVD2470 Deluxe Cabinet with C-Thru Doors features:

• Material: Deluxe Storage Cabinets, as well as all Tennsco Products, are fabricated of high quality, cold-rolled carbon steel, free of scale or rust, and fully pickled. Exposed edges, corners, and surface areas are free of sharp edges and all workmanship is of the highest quality as measured by the industry
• Finish: All steel components shall be thoroughly cleaned and phosphatized for rust resistance in a five-stage pre-treatment process. A high grade of polyester epoxy powder paint is to be applied electrostatically with a gloss reading of between 55 and 65. The finish shall have a salt spray rating of 250 hours or more
• Header: The header is 16 gauge steel, formed into a 1 11 / 16 Inches wide and 1 7 / 16 Inches deep “C” channel formation having a 25 / 32 Inches angle formation on the bottom leg of the header. The header is slotted to accept the lock bar from the three-point locking system. The header is welded to the frame making it an integral part of the frame assembly
• Sill: The sill is 16 gauge steel formed into a 4 Inch wide and 1 3 / 16 Inches deep “C” channel formation having a 13 / 16 Inches angle formation off the top leg of the sill. The sill is slotted to accept the lock bar from the three-point locking system. The sill is resistance welded to the frame making it an integral part of the frame assembly
• Side Frames: The side frames are 16 gauge steel formed into 1 Inch wide “C” channel formation and have a 1 1 / 2 Inches and a 21 / 64 Inches flange. The side frames are resistance welded to the header and sill
• Hinges: Hinges are semi-concealed, with five knuckles, a tight pin, and 16 gauge full loop hinges that are resistance welded to frames and riveted to the door. There are four hinges per door on 78 Inches cabinets and three hinges per door on 42 Inches cabinets
• Doors: C-Thru Doors are formed from 21 gauge steel with a 27 / 32 Inches flange on top and bottom. The doors are 1 Inch thick with a channel formation on the edges. The door strike on the left-hand door is hemmed for a smooth uniform edge. The doors are reinforced with a full-length door stiffener that is 4 1 / 8 Inches wide and 25 / 32 Inches high. The doors are designed in such a way to accept the standard three-point locking system
• Sides: Sides are formed from 22 gauge steel and have 3 / 4 Inches of 90-degree flanges on the top and the bottom. The sides have a 90-degree flange on the back for strength and an offset on that front to allow the side to fit flush with the frame. Each side has a dog ear strip to secure the shelves in place and allow for shelf adjustability on 2 Inch centers
• Back: The back is formed using 22 gauge steel and has 25 / 32 Inches and 90-degree flanges on the top and bottom. Welded cabinet backs have two, 4 11 / 16 Inches x 2 3 / 4 Inches louver clusters for ventilation, while KD backs have four. Each louver is formed to the inside of the cabinet. The backs have two rows of dog ear lances perforated in the back to secure the shelves and allow shelf adjustability on 2 Inch centers. Every third dog ear is shaped differently to make installation and line up of shelves easier.
• Top: The top is formed using 22 gauge steel and has 25 / 32 Inches of 90-degree flanges on all four sides
• Bottom: The bottom is formed using 20 gauge steel and has 25 / 32 Inches flanges on all four sides
• Shelf: 18 Inches of shelves are 20 gauge and 24 Inches of shelves are 22 gauge, flanged at the rear and ends. Box formation at the front. Adjustable on 2 Inch increments
• Handles: The cabinet has two brushed chrome handles. The right handle has a built-in lock and locks both doors, making the opening and closing of dual swing-out doors easy. The left dummy handle provides a pull for the door while giving an attractive appearance to the cabinet
• The locks are core removable and master keyed. Locks can be keyed to the same key as other Tennsco products
• Recessed Handle Units: 3 1 / 2 Inch diameter recessed handle with a built-in lock on the right-hand door
• Three-Point Locking System: The cabinet is equipped with a secure three-point locking system. The system consists of a locking cam that secures the two doors together with two 5 / 8 Inch x 1 / 8 Inch locking bars that lock the right door securely into the header and sill. The left door is held by the right door. The lock mechanism is operated by turning the right handle and the two lock bars will operate smoothly using nylon silencers
• Partition: Partitions are formed using 22 gauge steel and have 25 / 32 Inches flanges at the top, bottom, and rear with a formed bead in the front. The partitions have two rows of dog ear lances running vertical, designed to secure the shelf in place
• Partition Shelves: Partition shelves are formed with 22 gauge steel and have 1 1 / 8 Inches flanges at the rear and ends. They have a channel formation in front and are adjustable on 2 Inch increments
• Shelf Clip: Shelf clips are formed using 20 gauge steel. No hardware is required to hold the shelf
• Coat Rod: The coated rod is made using 20 gauge 5 / 8 Inches of O.D. plain steel tubing. Coat rods are installed into combination cabinets through coat rod brackets and secured with hardware screws on top of the bracket and the side
• Bolts & Nuts: For KD cabinets only bolts and nuts consist of a sealed plastic bag with 8-32- 1 / 2 Inch slotless headed bolts with hex nuts. All bolts have flush heads
• Brand: Tennsco
• Manufacturer: Tennsco
• Model: CVD2470
• Manufacturer Part Number: CVD2470
• Dimensions (W x D x H): 36.00 x 24.00 x 78.00 inch
• Weight: 183 lbs
• Limited Manufacturer Warranty