Tennsco LPL3624L20 2 High Lateral Files With Fixed Drawer Fronts - LPL3624L20

When office space is limited, Tennsco LPL3624L20 Lateral Files provide unlimited solutions. The practical design of these attractive files not only hugs the wall but also allows an easier, more efficient organization.

The LPL3624L20 files parts are of the gauges and are permanently fastened together in proper alignment by electric spot welding, arc welding, and brazing. All doors (12”) on the roll-out shelf lift up from the bottom, pivot on molded linear polyethylene door guides, and recess into the cabinet above the shelf. The door opening and closing motion is guided by nylon buttons and a spring-loaded “scissor” type equalizer. Both the open and closed position of the door is cushioned by rubber stops. Each roll-out shelf and drawer operates on a pair of telescopic, three members, full-extension, ball-bearing slides with 112 hardened steel balls. The rubber of felt cushioned stops are provided on both the opening and closing stroke of the drawer slide. Adjustable leveling glides are positioned one at each of the four corners. 

The glides give rigid support to the cabinet under full loads when fully extended. The glides are easily adjustable from both inside or outside of the cabinet (a maximum of 1 / 2 ”). Each roll-out shelf and drawer has a positive and automatic interlock mechanism to control the opening and closing of each drawer and/or shelf in the cabinet. When one drawer or shelf is extended two inches beyond the cabinet face, no other drawer or shelf will open. 12” roll-out shelves and drawers are equipped with hanging folder rods for support of either letter or legal size material in a lateral manner and accessory rods are available for filing letter or legal material in the front to back manner.

2 High Lateral Files With Fixed Drawer Fronts - LPL3624L20 features:

• Material: Laterals, as well as all Tennsco Products, are fabricated of high quality, cold-rolled carbon steel, free of scale or rust, and fully pickled. Exposed edges, corners, and surface areas are free of sharp edges and all workmanship is of the highest quality as measured by the industry.
• Finish: All steel components shall be thoroughly cleaned and phosphatized for rust resistance in a five-stage pre-treatment process. A high grade of polyester/epoxy powder paint is to be applied electrostatically with a gloss reading of between 55 and 65. The finish shall have a salt spray rating of 250 hours or more.
• Construction: The cabinet construction is exceptionally clean and smooth with rigid interior framing. All inside corner openings of all files are brazed together.
• Side Panel: The side panel is a single sheet, flanged at the rear, with a 5 / 8 ” face channel formed front.
• Uprights: The front uprights are formed with six bends and are rigidly reinforced at the extreme lower front area of the file by 11 gauge (.119) braces. The braces are arc welded to the front uprights, to the base, and to the 11 gauge corner gussets. Both front and rear uprights are slotted or pierced on 3” modular centers to accept door tracks, drawer slides and all other interior members. The 3” modular centers permit almost unlimited arrangements of shelf or drawer combinations in any cabinet height.
• Bottom Panel: The bottom panel consists of a separate base shelf, the channel formed on all four sides and the bottom front horizontal reinforcement base rail. The base rail is joined to the base shelf by spot welding. Additionally, four corner gussets are spot welded to the inside of the bottom panel
• Roll-out Shelf: The roll-out shelf consists of a one-piece bottom and back, a channel formed in the middle to accept a lateral operation follow block and two ends, flanged at the bottom and rear. The ends are slotted to accept hanging folder rods for either letter or legal material. The shelf bottom is slotted on 2” centers to accept dividers to serve as supports for filling material.
• Doors: All door fronts are box formed and are reinforced on both sides by door slide brackets. Drawer fronts are channel formed, top and bottom and with ends flanged and offset for spot welding to ends of roll-out shelf. Drawer inner panels are provided with all drawers. All short pull doors and drawer fronts are furnished with a durable black plastic recessed handle with a plastic chrome frame.
• Short Pulls: All short pulls for doors and drawers are located at the bottom of the door of the drawer. All long pull doors and drawer fronts have painted steel recessed pulls.
• Long Pulls: All long pull doors and drawer fronts have painted steel recessed pulls. All long pulls for drawers are located at the top of the drawer. All long pulls for retracting doors are located at the bottom of the door.
• Brand: Tennsco
• Manufacturer: Tennsco
• Model: LPL3624L20
• Manufacturer Part Number: LPL3624L20
• Dimensions (W x D x H): 36.00 x 17.94 x 27.56 inch
• Weight: 108 lbs
• Limited Manufacturer Warranty